AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Sweet home 3d kitchen island1/18/2024 ![]() I had at first got rid of the chairs and tried to use taller ones, but that just looked awkward, then I found this island at 3D Warehouse as well as a chair that matched the ones with the table set. Living Room, from the side door, looking toward the front door - another view of the change to the ceiling fan.ĭining Room/Kitchen, three different views - changed the island, as mentioned before, because I didn't like both how high serving side of the counter was in order for the preparation side to be the same height as the rest of the kitchen counter areas, and I didn't like how tiny the chairs were. The new Kitchen island is also somewhat visible here too. ![]() Living Room, from sitting in the middle of the corner couch - another view of the change to the ceiling fan. The new Kitchen island is also somewhat visible here. Here's a better view of the ceiling fan I kept its same dimensions but raised it 6 inches. ![]() Just inside the front door, looking toward the Living Room. You can also see the change in the shadow cast on the ceiling by the ceiling fan in the Living Room. I've changed the island in the kitchen you'll see it better in later pictures. Just inside the front door, looking toward the Kitchen. I just realized that I had forgotten to mention the small structure in the backyard it's a tool shed. Also visible in the third picture, on the North facing side of the house, you can see that in the front bedroom I've changed it from having three windows into two, and added two windows to the Master Bedroom. Virtual Visitor Entryway - just showing the couple of changes to the front from yet another angle.īack, three different angles - added hanging lights, and moved the table set more centered under one the lights. Virtual Visitor Front - just showing the couple of changes to the front from another angle. Also, showing the couple of changes to the front from a different angle. I think that's all that I've changed here.Īerial South facing side of the house - Level 1 windows have frosted glass, took out the single window in the Sewing Room between the back stairs and my bedroom door, and added three windows (with frosted glass) into the back stairs area. I'm going to post all of the pictures I have of this version - some old, some new.Īerial Front - added a mailbox, and took out the back pillars to the entryway as they didn't look right to me. Some rooms didn't change, and some rooms with more changes than others. and I couldn't help but make a few minor changes in other areas as well. and that's where I am now.Īlso, looking back at these pictures, I realized that the ceiling fan in the Living Room isn't even attached to the ceiling! Oops! So, back in I went to fix that. with what I've posted, even if they look like they're finished. I try to get good pictures for this forum.Īnd, you know me, I can never be. seeing as there are no longer any half round windows. Finally, I switched the placement of the window and the towel rack in the en suite bathroom.Īnd now that I look at these pictures. I also added the triangle gable vent in the attic in place of the half round window. Hopefully the difference isn't too noticeable. I couldn't actually get both sides the same width because that front section isn't centered. I used that along with the fixed window in the basic library. The windows in the front were bothering me being two different sizes, and I wasn't all that happy with the half round ones, so I found a window: My only goal is that all the world is winner.Once again, I've made a couple of changes. If they are opposed nevertheless to my activities, they will be necessary me for it to say so that Iimmediately stop sharing the products 3D which I modelled for them. If it is necessary to make petition for the convaincres which it is urgent to share their products in 3D with all the software of the trade, I would do it. The advantages of sharing files 3D under various software are:ġ) To gain new customers professionals who use other software that “ IKEA home planner ”.Ģ) To be to the forefront of technology by allowing the impression 3D of their products.ģ) To have a Free Publicity all owing a greater notoriety.Īs I am admiring of their company, I have write a mail asking for an authorization for my activities and I still do not have an answer. Their choice is astonishing since big distributors as the “ Maison du Monde ”remunerate computer graphics experts 3D to carry out their products which are then shared with the whole world on “ 3Dwarehouse ”. Re: Furniture Library Editor Beta released
0 Comments
Read More
Leave a Reply. |